Buy DIN EN ISO E: SAFETY OF MACHINERY – SAFETY DISTANCES TO PREVENT HAZARD ZONES BEING REACHED BY UPPER AND LOWER. Safety of machinery – Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO/DIS ); German and English version. Safety of machinery – Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO ); German version EN.
|Published (Last):||11 September 2014|
|PDF File Size:||2.47 Mb|
|ePub File Size:||19.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
Your Alert Profile lists the dkn that will be monitored. There shall be no interpolation of dim values given in Table 2. We have no amendments or corrections for this standard. For dated references, only the edition cited applies. Skip to main content. Find Similar Items This product falls into the following categories. If the height, a, of the hazard zone is 1 mm and its horizontal distance, c, from the proposed protective structure is mm, then, using Table 2, the height, b, of the protective structure can be determined as follows.
Free download: EN ISO 13857 Safety Distance Calculator
Procter Machine Guarding recommends that a risk assessment is always carried out, for which the company offers a free Risk Assessment Calculator. You may experience issues viewing this site in Internet Explorer 9, 10 or Who should buy it? Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding Essential Requirements 1.
The dimension of the opening, e, corresponds to the side of a square opening, the diameter of a round opening and the narrowest dimension of a slot opening.
As with the standard, the calculator also gives the safety distances for slots, round, square and irregularly shaped apertures through which a person could reach. For machines which are covered by the dn of a type C standard and which have been designed and built according to the provisions of that standard, the provisions of that type C standard take precedence over the provisions of this type B standard.
NOTE 2 These safety distances will not provide sufficient protection against certain hazards, for example, radiation and emission of substances.
In such cases, at least protective structures to restrict the free movement of the lower limbs should be used. Because safety distances depend on size, there will be some people dkn extreme dimensions who will be able to reach hazard zones even when the requirements of this International Standard are complied with.
Izo is incorporated by Royal Charter. There should be no interpolation between the values in this table. Positioning of safeguards with respect to the approach speeds of parts of the human body. NOTE 2 These safety distances will not provide sufficient protection against certain hazards, for example, radiation and emission of substances.
Enter the email address you signed up with and we’ll email you a reset link.
Consequently, when the known values of a, b or c are between two values in Table 2, the greater safety distance or higher 1357 structure or change in the height higher or lower of the hazard zone shall be used. Contact the Information Centre. The safety distances are appropriate for protective structures. For such hazards, additional or other measures need to be taken. Other topics include biomechanical factors, such as compression and joint rotation limits; vin and practical aspects; and additional measures for persons who might deviate from the specified body dimensions.
International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Proceed to Checkout Continue Shopping. Although it is based on a Microsoft Excel spreadsheet, no knowledge of this software package is required in order to use the Calculator.
BS EN ISO 13857:2008
In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. It is the constant aim of BSI to improve the quality of our products and services. Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.
The corresponding value for the height, b, of the protective structure is 1 mm see e. Users of British Standards should make sure that they possess the latest amendments or editions.
Take the smart route to manage medical device compliance. Safety distances shorter than mm see Table 4 may be used when the obstacle limiting the movement is at least mm long. If the height, b, of the protective structure is 1 mm and the height, a, of the hazard zone is 2 mm, then, using Table 2, the horizontal safety distance, c, from the hazard zone can be determined as follows.
Users are responsible for its correct application. The corresponding value for a is 2 mm or more, or 1 mm or less see e. Your basket is empty. It also gives information about distances to impede free access by the lower limbs see 4. It also shares reliable surveys of anthropometric data based on the population groups most likely to be found in the relevant countries. The safety distances are intended to protect those persons trying to reach hazard zones under the conditions specified see 4.
mk_Profiltechnik__en – Page
Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service.
The work of preparing International Standards is normally carried out through ISO technical committees. It also gives information about distances to impede free access by the lower limbs see 4. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
These best practice recommendations include body dimensions, length, machine guards and barriers or holes. General principles for design.