Correction in Service Manual. CX New camera body – new parts .. The operation (except ELX) is fortunately a matter of minutes only. Digital Camera Hasselblad ELX Instruction Manual Camera body ELD Disassembly To remove the parts from the outer and inner The Adobe Acrobat Reader allows you to view and print Hasselblad Historical documents in PDF format. A free copy of the Acrobat Reader is available from.

Author: Tojamuro Nimi
Country: Nicaragua
Language: English (Spanish)
Genre: Technology
Published (Last): 20 October 2008
Pages: 247
PDF File Size: 2.48 Mb
ePub File Size: 10.31 Mb
ISBN: 721-9-28315-551-2
Downloads: 56430
Price: Free* [*Free Regsitration Required]
Uploader: Yozshuhn

If you find yourself with a lens and tube s or extender stuck on the body and you can’t get the assembly on or off, take the camera to a Hasselblad technician who can remove the components without causing damage to the camera.

However, if i nudge the little poked-out head of the release lever with my finger pressing lightly down on it the shutter will then fire as expected!

Dirt and dust get into your camera, and lubricants dry out and get thick. The newer A magazines repaig not have a number 0. When you press it in, the diaphragm blades should quickly snap closed.

HASSELBLAD Camera Manuals

At that point, lift the transport key again and wind it through at least six or seven turns to wind up the backing paper trailer before opening the magazine and removing the film. Use extreme caution when following this procedure! Camera body ELD Reassembly The key position of the front gear is checked with the Position for screw driver camera cocked. When handling the circuit board a grounded bench mat and a wrist strap must be used to prevent ESD damage.

Remove the lens and magazine. If I replace a brake assembly in your camera body, it is because you had the older style brake. Set the f stop ring to hass,eblad smallest setting largest numberand move the stop down lever to the stopped down position. Camera body ELD Adjustment Checking the databus connections Check the integral control connector to ensure automatic and rdpair communication between camera body and digital back.


Camera body ELD Disassembly Rear plate Remove the screw from the centre of the large gear and lift the gear clear.

Hasselblad 555ELD Service Manual

What is the proper procedure for attaching or removing extension tubes? It also prevents the camera from firing when the dark slide is inserted, and prevents the removal of the film magazine from the camera body when the dark slide is removed. EPS Refit the gearwheel temporarily. Parts for the older C lenses are no longer being manufactured, and the availability of these parts is limited to the existing supply.

Lubricate with Isoflex Topas L32 onto the pin for the teflon button and put that one in position before inserting the camera body into the camera shell.

Remove the pinspring retainer, spring and the upper actuating arm There is no way to properly repair a cracked flap; it has to be replaced. At this point, the number wheel will show the number 1 in the window.

500 EL/M won’t fire with pressing of release button

But the shutter in the lens doesn’t open for the exposure. Back to Top How can I check my camera to make sure that it is working properly?

Not with the brake, but with some technicians. When this happened, the flaps couldn’t open and close properly and the camera would jam up. Camera body ELD Hassleglad Remove the two long screws located towards the front of the camera shell.

This is carried out as follows: I’m off to bed now without having my supper. You will notice an opening of the same size in the upper left hand corner of the rear plate. Instead, push the button on the top of hasslblad magazine over with your thumb before attaching the magazine to the body. The repairs are really, very simple to do. The number wheel should return back to number 0. Check that the plug fits smoothly, without gaps.


Then move the lever to the “O” position, and the camera will finish the cycle.

This manual contains 98 pages and is a photocopy of the original. Shine a light source towards the oval cut-out in the upper part of the tube so that the white ring of the ocular is illuminated. Continue turning the screwdriver clockwise until it won’t turn anymore.

Back to Top Is it better to store my camera bodies and lenses wound or in the tepair position?

Pull the paper leader around to the take up side, and insert the end of the leader flm the slot on the take up spool. Attaches to the front release ports hhassleblad the camera and powered by the camera batteries. When this happens, you will feel a binding sensation when you start to wind the body. Take the magazine off the body and remove the dark slide. Page 13 Camera body ELD Disassembly Mirror Disconnect the mirror hinge from the two pins “A” and release the pin “B” on the mirror frame, from the mirror lever Connect the mirror hinge to the two pins “A”.

Hasselblad Historical – V-System manuals

Camera body ELD Reassembly Seal between the rear plate and the left side wall using black silicone or similar as shown in Fig. First, there is the shutter blade itself. Here are some sample pages from the Film Magazine Repair Manual. Everything on it works well, except for the shutter release. So mqnual majority of EL Why did one of my shutter blades break?